Knowledge-based diagnosis of drill conditions

One major bottleneck in the automation of the drilling process by robots in the aerospace industry is drill condition monitoring. This paper describes a system approach to solve this problem through the advancement of new machine design, sensor instrumentation, metal-cutting research, and intelligent software development. All drill failures can be detected and distinguished: chisel edge wear, flank wear, crater wear, margin wear, corner wear, breakage, asymmetry, lip height difference, and chipping at lips. However, in the real manufacturing environment, different workpiece materials, drill size, drill geometry, drill material, cutting speed, feed rate, etc. will change the criteria for judging the drill condition. The knowledge base used for diagnosing the drill failures requires a huge data bank and prior exhaustive testing. A self-learning scheme is therefore introduced to the machine in order to acquire the threshold history needed for automatic diagnosis by using the same new tool under the same drilling conditions.     

库岸滑坡稳定可靠性分析中若干规律的探讨

采用可靠性分析的Monte-Carlo法，对中岸滑坡稳定可靠性分析中的有关规律进行了探讨。指出了影响滑坡体稳定的有关因素及其变异性对破坏概率的影响。     

精轧油膜轴承密封失效机理的初步分析

对油膜轴承密封出现的进水、漏油现象作了大量的调查、测量和统计分析，找出了产生质量事故的根本原因，提出了解决措施。     

Fault-accommodation with intelligent sensors

Optimal sensor fault-accommodation is considered for faults modelled by an increase in measurement noise. This noise is taken to be bounded and its probabilistic properties unknown. It is assumed that intelligent (e.g. self-validating) instrumentation is in use and estimates of the noise bounds are available. The fault-tolerant controller is designed to optimize a noise rejection and a nominal reference tracking index and leads to a mixed norm minimization problem (l₁/l₂). We exploit known results and a particular feedback configuration to show that it is possible to optimize simultaneously without a trade-off the two performance indices. The results are applied to systems where the presence of auxiliary measurements allows for an optimal fault-accommodation strategy. Using properties of the optimal solution, we define a factorization for the optimal controller alternative to the Youla parametrization, leading to an algorithm which is optimal, transparent and efficient.     

Macha爆炸机故障维修十一例

随着Macha遥爆系统在地震勘探中使用年限的增加，该系统在工作中时常出现各种各样的故障，本文根据其日常检修记录，分析总结了Macha系统常见的十一例故障，并从故障的现象、分析、排除三个方面对各个故障进行了详细的介绍。     

八钢高炉无料钟炉顶的装料制度

以八钢高炉炼铁实践为依据，系统研究和分析了八钢2号和3号高炉炉顶设备装料制度对高炉冶炼的影响。认为高炉操作制度是当前高炉炼铁的主要技术之一，也是影响高炉焦比主要技术经济指标的重要因素。在原燃料和装备水平一定的条件下，合理的操作制度对高炉的技术经济指标起到决定性的作用。     

疏松砂岩地层出砂对套管损坏的研究

以东濮凹陷文明寨油田历年井况调查的套管损坏资料为依据，在对出砂油井套管损坏形态、层位与射孔状况、岩石性质等因素进行综合分析基础上，对疏松砂岩出砂、上覆岩层坍塌等主要方面导致的套管受力变形进行研究，为探讨防治措施提供依据。     

塔里木盆地塔河油田原油中双金刚烷分布特征与油气运移

研究了塔里木盆地塔河油田原油中双金刚烷的分布特征，探讨了该油田油气的充注期次和运移方向，结果表明，原油中双金刚烷指标值反映了原油的成熟度，并且指示研究区4区和6区原油充注时间较早、9区原油充注时间较晚，其它油区原油充注时间介于上述二者之间；原油中双金刚烷指标值分布特征显示出塔河油田下奥陶统油气存在2个充注方向，一是由南向北，并且油气成熟度相对较低，可能主要代表了早期的油气运移，另一个是由东向西，原油成熟度相对较高，可能主要代表了晚期的油气运移。根据原油成熟度和运移方向特征，认为塔河油田的早期油气起源于满加尔坳陷，晚期油气起源于满加尔坳陷和草湖坳陷，主力烃源岩层为寒武-奥陶系。     

DIN-100MnCrW4模具钢开裂原因分析

对DIN－100MnCrW4模具钢开裂原因进行了分析。结果表明，模具钢 属淬火开裂，主要原因是材料内部组织不均匀所致。     

炉壁集束碳氧枪在电炉中的应用

介绍了鄂钢电炉厂70t consteel 电炉使用炉壁集束碳氧枪后对经济指标的改善,以及在生产实践中的冶金效果.